SYSTEM Air ConditionersINSTALLATION MANUALCAREFULLY READ THESE INSTRUCTIONS BEFORE INSTALLATION.KEEP THIS MANUAL IN A HANDY PLACE FOR FUTURE REFERENCE
9 English(5) When hanging the indoor unit, make sure to use the level to have better drainage and install it hor-izontally. Also, if it is possible at
English 10• When connecting the pipings to the air conditioner, make sure to use a spanner and a torque wrench as shown in Fig. 13.For the dimension o
11 English• After leak test, referring to Fig. 15, insulate both the gas and liquid piping connection with the attached joint insulating material (6)
English 12(1) For rear side piping• Remove the rear piping penetration cover, and connect the piping. (Refer to Fig. 16 and 18)(2) For upward piping•
13 English• Before brazing refrigerant piping, have nitrogen flow through the refrigerant piping and substitute air with nitrogen. Then, carry out bra
English 147. DRAIN PIPING WORK(1) Carry out drain piping.• Carry out drain piping so that drainage can ensured.• Drain piping can be connected from th
15 English• Make sure to use the attached drain hose (1) and metal clamp (2). Also, insert the drain hose (1) into the root of the drain socket, and t
English 16< CAUTION >• To avoid the attached drain hose (1) getting excessive force, do not bend nor twist it. (It may cause water leakage.)• Wh
17 English8. ELECTRIC WIRING WORK8-1 GENERAL INSTRUCTIONS• Make certain that all electric wiring work is carried out by qualified personnel according
English 188-4 WIRING CONNECTION METHOD<<Caution for wiring>>• The indoor units in the same system can be connected to the power supply fro
1 EnglishFXHQ32AVEBFXHQ63AVEBFXHQ100AVEBVRV SYSTEM Air Conditioners Installation manualCONTENTS1. SAFETY PRECAUTIONS ...
19 English<Power supply wiring • earth wiring • remote controller wiring • transmission wiring connecting method>(1) Hold the control box, loose
English 20CAUTION• When conducting wiring work, do not touch the printed circuit board. It may cause failure.• Never connect the power supply wiring t
21 English8-5 EXAMPLE OF WIRING<< No. 1 system: When 1 remote controller is used for 1 indoor unit. >><< No. 2 system: When carrying
English 22<< No. 3 system: When BS unit is used >>WARNINGBe sure to install an earth leakage breaker.Failure to do so may cause electric s
23 English8-7 FOR CENTRALIZED CONTROL• When centralized equipment (such as centralized controller) is used for control, it is required to set the grou
English 249. MOUNTING SUCTION GRILLE · DECORATION SIDE PANELInstall securely in the reverse order when decoration side panel and suction grille were r
25 English10-1 SETTING OF CEILING HEIGHT• Set the SECOND CODE No. according to the ceiling height as shown in the Table 3. (The SECOND CODE No. is set
English 26<Test operation>• After cleaning the indoor unit inside and the suction grille, carry out test run according to installation manual at
27 English3D079560-1 FXHQ32 • 63 • 100AVEBA1PC105F1UHAPKPRM1FM1SPSR1TR2TR3TV1RX1MX2MY1EZ1FX15AX24AX25AX33AX35AWIRED REMOTE CONTROLLERTHERMISTOR (AIR)P
(1209) HT3P249378-8N EM12A00900_CV_3P249378-8N.fm Page 2 Sunday, September 30, 2012 4:47 PM
English 2• Be sure to use only the specified parts and accessories for installation work. Failure to use the specified parts may result in the air co
3 English2. BEFORE INSTALLATIONWhen unpacking and moving the indoor unit after unpacked, do not apply force to the piping (refrig-erant and drain) and
English 42-2 OPTIONAL ACCESSORIES• For this indoor unit, the remote controller is separately required. • There are 2 kinds of remote controller; wired
5 EnglishPoints of the operation explanation3. SELECTION OF INSTALLATION LOCATIONWhen unpacking and moving the indoor unit after unpacked, do not appl
English 64. PREPARATION BEFORE INSTALLATION(1) For the locations of indoor unit hanging bolts, piping outlet holes, drain piping outlet hole, and el
7 English(3) Remove the parts of the indoor unit.1) Remove the suction grille.• Slide the suction grille fixing knobs (32 type: 2 places for each, 63,
English 8(4) Install the hanging bolts. • Use M8 or M10 bolts for hanging the indoor unit.• Adjust the length of the hanging bolt from the ceiling in
Commentaires sur ces manuels